Hi,
I want to cut a raster with shp file, and the result raster will have the extent of the clipper's instead of the clippee's. (consider null or nodata as filled up)
david_r wrote:
Not sure I fully understand, but is it perhaps the RasterTiler that you are looking for?
When I clip a raster with shp polygon, I want the raster will take the polygon extend if there are places the raster it was not covered, then the result can be filled up with 0.
If you can understand me better now.
+17- Contributor
The Clipper transformer should be able to do that. Shape as Clipper, raster as Clippee, output from Inside (or in older versions Clipped_Inside.
Make sure both data sets are in the same coordinate system.
+28- Contributor
Use the clipper, make sure Preserve Clippee Extents is set to No. You can explicitly set the NoData value before hand by using the RasterBandNoDataSetter, if you don't it defaults to 0
+19- Contributor
Does this screenshot illustrate your requirement?
Two green checkerboards are original rasters, and red squares represent the extents of resulting rasters i.e. clippers' extents.
takashi wrote:
Does this screenshot illustrate your requirement?
Two green checkerboards are original rasters, and red squares represent the extents of resulting rasters i.e. clippers' extents.
+19- Contributor
bonbon wrote:
yes! Each read polygon is a tiled raster. So it will end up in 7 small rasters with same extents and same resolution.
Assuming that the clippers (tiles) have column index and row index which can be used to identify each tile.
- BoundsExtractor: Extract extents (xmin, ymin, xmax, ymax) for each clipper.
- Clipper: Merge clipper's extents to clipped rasters.
- MapnikRasterizer: Render the clipped rasters onto clipper's extents.
+19- Contributor
bonbon wrote:
yes! Each read polygon is a tiled raster. So it will end up in 7 small rasters with same extents and same resolution.
takashi wrote:
If the number of tiles is very large, it might be better to sort the clipped rasters by column and row indices and set 'Yes' to the 'Input is Ordered by Group' parameter in the MapnikRasterizer.
bonbon wrote:
Solved and thanks!! ^^
I have similar problem.
I want to clip a raster (MDT=1 band) -generated from 2 asc files (no problem)- to many tif tiles following exact coordinates extracted from a shapefile. If tiles are smaller than the extend of shape, they should be filled with any value but the tfw of tiles should be exactly the same the coordinate of the clipper (shape).
When I appy Clipper tranformer, the coordinates are not exactly the same of the shape. When I add also Mapnik Rasterizer, the results are tiles on coordinates ok following the shape, but they are RGB type and no data values in all the tiles (empty tiles). In attachment the model. thanks
mosaico.jpg
mosaic-clip.fmw
Hello,
I have a similar problem but I havent solved it yet.
I have a raster 1 band extracted from asc files (no problem). I want to tile it in different tiles following coordinates extended of a shapefile. If the tiles dont cover the shape extend they should be filled with any value but the coordinates should be the same than the shapefile (clipper).
If I apply only Clipper tranformer the tiles are ok but the coordinates extend dont follow the shape extend because the tiles are smaller and dont fill the no data.
If I also add Mapnik rasterizer the coordinates of tiles are ok but the tiles are RGB and empty.
Many thanks!
mosaico.jpg
+19- Contributor
gossyrossa wrote:
Hello,
I have a similar problem but I havent solved it yet.
I have a raster 1 band extracted from asc files (no problem). I want to tile it in different tiles following coordinates extended of a shapefile. If the tiles dont cover the shape extend they should be filled with any value but the coordinates should be the same than the shapefile (clipper).
If I apply only Clipper tranformer the tiles are ok but the coordinates extend dont follow the shape extend because the tiles are smaller and dont fill the no data.
If I also add Mapnik rasterizer the coordinates of tiles are ok but the tiles are RGB and empty.
Many thanks!
mosaico.jpg
clip-raster-demo.fmwt (FME 2018.0.1.1)
gossyrossa wrote:
Hello,
I have a similar problem but I havent solved it yet.
I have a raster 1 band extracted from asc files (no problem). I want to tile it in different tiles following coordinates extended of a shapefile. If the tiles dont cover the shape extend they should be filled with any value but the coordinates should be the same than the shapefile (clipper).
If I apply only Clipper tranformer the tiles are ok but the coordinates extend dont follow the shape extend because the tiles are smaller and dont fill the no data.
If I also add Mapnik rasterizer the coordinates of tiles are ok but the tiles are RGB and empty.
Many thanks!
mosaico.jpg
+19- Contributor
gossyrossa wrote:
takashi wrote:
If I understood your requirement correctly, the attached workspace might help you.
clip-raster-demo.fmwt (FME 2018.0.1.1)
data.zip
+19- Contributor
takashi wrote:
If I understood your requirement correctly, the attached workspace might help you.
clip-raster-demo.fmwt (FME 2018.0.1.1)
- 3DForcer: the Elevation parameter
- NumericRasterize: the Background Value parameter
Then, remove the RasterBandNodataSetter from the workflow.
+19- Contributor
takashi wrote:
If I understood your requirement correctly, the attached workspace might help you.
clip-raster-demo.fmwt (FME 2018.0.1.1)
+8Also make sure to have the same value for the Group By attritube on both raster and clipper(s) if you use the clipper in Group By mode.
Reply
Most helpful members this week
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.